Pelletburner - grain, pellets - MOC CWD 15- 300 KW

Pelletburner M.O.C with capacity range 15- 300 kW is designed to heat houses, bakeries, farms, commercial buildings. Burner can be built in in new pellet-boiler like Futura Pel-lets but as well in existing oil or coal boiler. Our burner can burn pellets with 6/8 mm diameter and also grain.

Pelletsburner M.O.C has a lot advantages for end user :

• Cast iron grate - burner head with pneumatic air cleaning system
• Feeder 1,7 m and burners head are galwanized
• Sensor of furnace temperature and Lambda probe optional
• Electronic controller with 2 pumps controller and as optional with mixer controll and LCD display
• 2 screws - one in the feeder , second in the burner to avoid sintering of the fuel

FUEL
Wood pellet 6-8mm cross section , length 5-30mm, ash content max. 2%. The maximum moisture content of pellets should not exceed more then 10%. The calorific value of the pellets should be greater than 17,5 MJ/kg. Pellets made in accordance with Standard: •    ÖNORM (M7135) or DIN-Norm (DIN-Norm 51 731). •    Cross section: 6-8 mm, length: 5–30 mm •    Max. Ash content 2% •    Calorific value > 17,5 MJ/kg
CONSTRUCTION OF THE BURNER
1.    Gear motor with electric drive 2.    Pellet feeding tube 3.    Electrical connector (Plug) 4.    Internal burner feeder (Stoker) 5.    Furnace heat shield 6.    Cast iron grill 7.    Furnace body 8.    Electric igniter 9.    The air fan 10.  Burner’s steel cover 11.  Photosensor
INSTALATION DIAGRAM
	1.    Follow the burner mounting hole in existing door or additional mounting plate. 2.    Seal the space between the burner and door gasket with non-combustible material (high-temperature insulating boards, mineral fiber gaskets, etc.). 3.    Remove the burner housing (cover). 4.    Mount the burner on the door. Tighten it with screws. Bolt holes are located on the sides of the mounting flange of the burner. 5.    Connect the burner to the controller and mount the temperature sensor of the measuring tube boiler in the boiler. Attach the main feeder outside the fuel tank and connect it to the controller. Note the notch on the part of the feeding tube which is mounted in the tank and set it so that pellets fell into this hole. Install flexible tube connecting the burner with a feeder outside and secure it with straps.
SPARE PARTS
	1. Grate seal 2. Cast iron grate 3. mounting hole seal 4. Combustion part (Burner’s exchanger) 5. Combustion heat shield 6. Fan blower type: G2E097-HD01-02 7. Electrical connector 8. Back part of the burner 9. Sealing of the stoker tube 10. Sealing the back cover 11. Igniter 12. Internal burner’s feeder (stoker) 13. Feeding tube (pipe) 14. Back Cover 15. Gear motor with electric drive type: 4GN180K 4 IK25GNC 16. Outside cover of the burner 17. Outer tube feeder 18. Snail feeding tray 19. Mounting plate for feeding tray 20. External screw drive 21. Hose clamp 22. Flexible hose feeder

Pelletburner M.O.C with capacity range 15- 300 kW is designed to heat houses, bakeries, farms, commercial buildings.Burner can be built in in new pellet-boiler CWD like Futura Pel-lets but as well in existing oil or coal boiler. Our burner can burn pellets with 6/8 mm diameter and also grain. Pelletsburner CWD has cast iron grate - burner head with pneumatic air cleaning system and feeder 1,7m.Burner head are galwanized.